Technical data for CEV65M-01460 |
NO.OF STEPS/REV 4.096,000 |
NO. OF REVOLUTIONS 4.096,000 |
PROGRAMMABLE PROG. |
INTERFACE PROFIBUS DP |
CODE PROGRAMABLE |
OUTPUT LEVEL RS485 |
SUPPLY VOLTAGE 11-27V |
CONNECTOR TYPE 3XPG9 |
CONNECTOR-POSITION PG RADIAL |
MATING PLUG NO |
FLANGE TYPE ZB36 |
SHAFT TYPE 10FL/19,5 |
TEMPERATURE RANGE -20+70°C |
PROTECTION Class IP65 |
OPTIONS ENC 12MBAUD |
PNO-PROFILE CLASS.2 |
PINOUT NO. TR-ECE-TI-D-0017 |
DRAWING NO. 04-CEV65M-M0003 |
VERSIONNO 000 |
FIRMWARE NO 437826 |
Subject to change. |
General data for K-CEV65-PB-1 |
Nominal voltage |
- Specific value 24 VDC |
- Limit values, min/max 11/27 VDC Nominal current, typically |
- Specific value 120 mA |
- Condition unloaded |
Device design |
- Type Single-/Multi-Turn |
Total resolution <= 31 Bit |
Number of steps per revolution <= 8192 |
Number of revolutions <= 256000 |
Output capacity <= 25 Bit |
PROFIBUS - Interface |
- PROFIBUS-DP V0 IEC 61158, IEC 61784 |
- PNO Encoder-Profile Class 1 and 2 SSI - Interface |
- Equipment Optional interface |
- SSI-Clock input Optocoupler |
- SSI-Data output RS-422, 2-wire |
- SSI-Clock frequency 80…1000 kHz |
- SSI-Mono time, typically 18 µs Incremental - Interface |
- Equipment Optional interface |
- Incremental signals, square K1± K2± |
- Impulses, square wave 1024 or 2048 |
- Output driver, TTL RS-422, 5 VDC Transmission rate |
- Specific value 9.6…12000 kbit/s |
Cycle time 250 µs |
Parameter/Function, changeable Resolution Output code Limit switch |
External Preset inputs Adjustment - Parameter SSI-Parameter Counting direction Gear function |
Velocity parameter |
Type of parametrization programmable |
Subject to change. |
General data for K-CEV65-PB-1 continuation |
Programming - Tool Fieldbus-Device External inputs |
- Preset electronic adjustment |
- Logic level "0“ < +2V, "1“ = Supply |
Maximum Speed, mechanically <= 6000 1/min |
Shaft load, axial/radial <= 40 N, <= 60 N |
Bearing life time >= 3.9E+10 revolutions Bearing life time - Parameter |
- Speed 3000 1/min |
- Operating temperature 60 °C |
- Shaft load, axial/radial <= 20 N, <= 30 N |
Point of origin, shaft load at the shaft end Shaft type |
- Shaft diameter [mm] 6 |
- Shaft diameter [mm] 8 |
- Shaft diameter [mm] 10 |
- Shaft diameter [mm] 12 |
- Shaft diameter [mm] 14 |
- Shaft diameter ["] 3/8 |
Angular acceleration <= 10E+4 rad/s² |
Moment of inertia, typically 2.5E-6 kg m² |
Start-up torque, 20 °C 2 Ncm |
Mass, typically 0.7 kg |
Environmental data |
Vibration |
- Specific value <= 100 m/s² |
- Sine 50…2000 Hz |
Shock |
- Specific value <= 1000 m/s² |
- Half sine 11 ms |
Immunity to disturbance DIN EN 61000-6-2 |
Transient emissions DIN EN 61000-6-3 Working temperature |
- Standard 0…+60 °C |
- Optional -20…+70 °C; |
Storage temperature, dry -30…+80 °C |
Subject to change. |
Environmental data continuation |
Relative humidity 98 %, non condensing Protection class |
- Standard IP65 |