CHI TIẾT

SAFE BOX: LIMAX34 SAFE | LIMAX44 SAFE

SAFE BOX

Electronic evaluation unit in which safety-relevant switching and control functions are implemented
Up to 4 pairs of safety relays
ETSL delay control, end positions, door zones, safety brake release
Flexibillity in the adaption and expansion of the implemented switching and safety functions
Up to 29 safety inputs, 8 outputs
2 safety circuit inputs (110V, 220 VAC or 48 VDC)
DS406 or DS417 CAN interface for parameter setting or car position transmission, optional SIL3 CAN interface possible

LIMAX34 SAFE | LIMAX44 SAFE

For hoisting heights up to 260 m | speeds up to 10 m/s

Modular system consisting of the LIMAX33 RED sensor for safe detection of the car position and the SAFE BOX electronic evaluation unit, in which the car position and speed-dependent switching and control functions are integrated.

LIMAX44 SAFE

For hoisting heights up to 1,500 m | speeds up to 18 m/s

Modular system consisting of the LIMAX44 RED sensor for safe detection of the car position and the SAFE BOX electronic evaluation unit, in which the car position and speed-dependent switching and control functions are integrated.

Technical Data SAFE BOX

Mechanical Data

Housing material

aluminium

Housing dimensionsL x W x H

SAFE Box L: 220 x 134 x 97 mmSAFE Box XL: 220 x 134 x 134 mm

Cable length

1,5 m standard-cable length

Weight

SAFE Box L: approx. 1,640 gSAFE Box XL: approx. 1,800 geach without cable

Electrical Data

Power supply

24 VDC, +20 % / -25 %

Current consumption

SAFE Box L: max. 400 mASAFE Box XL: max 500 mA

Interfaces

CANopen (DS406), others on request

Number of safe inputs

SAFE Box L: 7SAFE Box XL: 21 + 8

Number of outputs

SAFE Box XL: 8

Number of safety circuit inputs

2 (110 V, 220 VAC oder 48 VDC)

Safety Relais

Voltage

230 VAC / 110 VAC / 24 VDC

Contact rating

max. 2 A

Quantity

Connection Sensor

Power supply

24 VDC

Interface

RS485

Environmental Condition

Storage temperature

-25 ... +85 °C

Operation temperature

-10 ... +70 °C-25 ... +85 °C on request

Humidity

max. 95%, non-condensing

Protection class

IP54, higher on request

THÔNG SỐ KỸ THUẬT

Sensors

Shaft Information Systems for the lift industry

Magnetic length and angle measuring systems

up to 1/10 resolution

Magnetic length and angle measuring systems

up to 1/1000 resolution

Rotative measuring systems

AbsoluteLIMAX Shaft Information Systems

Absolute measurement of the car position

For hoisting heights up to 130 m | Speeds up to 4 m/s

Absolute measurement of the car position

For hoisting heights up to 260 m | Speeds up to 10 m/s

Absolute, redundant measurement of the car position

For hoisting heights up to 260 m | Speeds up to 10 m/s

LIMAX SAFE Shaft Information and Safety System

Absolute, redundant recording of the car position.

For hoisting heights up to 260 m | Speeds up to 10 m/s

Absolute, redundant recording of the car position for the highest buildings.

For hoisting heights up to 1,500 m | Speeds up to 18 m/s

Electronic evaluation unit in which safety-relevant switching and control functions are implemented

Modular system consisting of the LIMAX33 RED sensor and the SAFE BOX.

For hoisting heights up to 260 m | Speeds up to 10 m/s

Modular system consisting of the LIMAX44 RED sensor and the SAFE BOX

For hoisting heights up to 1,500 m | Speeds up to 18 m/s

Shaft information system based on the LIMAX33 RED sensor for safe position detection. The safety-related switching and control functions are integrated in the sensor housing.

For hoisting heights up to 260 m | Speeds up to 10 m/s

Absolute

For industrial applications with a resolution of 1 mm and measuring lengths up to 1000 meters

Autoreferencing, absolute measuring system with a resolution of 1 mm and measuring lengths up to 1000 meters

Incremental

For angular and linear measurements, with 0.1 mm (0.025 mm) resolution.

Suitable for long distances, with 2.5 mm resolution.

1.0 mm resolution, up to 10 mm distance between sensor and magnetic tape possible.

Low-cost length and angle measuring system, with 0.1 mm (0.025 mm) resolution.

Round sensor with 0.1 mm (0.025 mm) resolution.

Absolute

Absolute, contactless measuring. With LED and SSI error bit if the distance between sensor and tape gets too large. Resolution 0.01 mm, for measuring lengths up to 20 meters.

Magnetic absolute length measuring system for highly dynamic controls

Absolute, guided measuring. Resolution 0,01 mm.

Incremental

Ideal for angular and linear measurements, with 0.01 mm resolution.

High Precision Length Measuring System with selectable resolution up to 0.001 mm (1 µm).

High precision length measuring system with selectable resolution up to 0,025 mm (2,5 µm).

Precision carriage for incremental measurements with pre-installed, selectable measuring system.

With speed monitoring and 5 adjustable resolutions. Guided Length Measuring System with a mechanical cylinder with resolutions from 0,1 mm to 0,001 mm.

Magnetic-based Length Measuring System with sin/cos signal output.

Magnetic-based Length Measuring System with integrated Push-Pull signals for MIN/MAX-limit switches.

Guided Measuring System for use in press brakes with a resolution of up to 0,00122 mm.

Absolute

Magnetic absolute encoder. High resolution: 16,000 mesauring steps/rev.

Single-Turn-Encoder. Resolution of 12 bit over the whole measuring distance.

Single Axis Absolute Inclinometer. Measuring range 0° to 90° with analog output 0,5 - 4,5 V.

3 Axes Absolute Inclinometer with high resolution. Measuring range 0° to 90° +/- with 0,025° resolution.

Incremental

Suited for rotative angular measurement. Wearfree due to contactless measuring principle. Up to 10 000 revolutions/minute.

Space-saving and reasonably priced option to rotary encoders. Insensitive against environmental influences. Can be used with all standard incremental ELGO sensors.

Incremental Encoder with 500 pulses/revolution, with 6 mm steel shaft, robust design, IP64.

Incremental Encoder with 500 pulses/revolution, with 6 mm steel shaft, IP54.

Incremental Encoder up to 500 pulses/revolution, with 10 mm steel shaft, IP54.

Incremental Encoder up to 1000 pulses/revolution, with 12 mm steel shaft, IP66

Hollow Shaft in miniature structural shape, IP54

Inclinometers

AbsoluteSingle axis absolute inclinometer: +/- 90°with Analogue output 0.5 - 4.5 V

High resolution 3 axisabsolute inclinometer:+/-90°, +/-90° / +/-180°with 0,025° resolution

Position Indicators - Power supply

1-axis mini position indicator 24 VDC

1-axis universal position indicator

1-3-axis position indicator

LED position indicator with two pre-selections and relay outputs

Universal position indicator for incremental and absloute measuring systems with relay outputs and integrated RS-232-interface

Battery-powered Position Indicators

For incremental measurementsSmalest design with integrated or external battery.

Battery-powered position indicator for length and angle measurement with resolution up to 0.01 mm

Battery powered position indicator with 7-digit LCD-display, a resolution up to 0.01 mm and "°"-symbol. Option: RS232-interface.

Battery-powered position indicator with an external sensor and 868 MHz radio transmission.

Battery-powered measuring and indicating system with large two-line LCD-display.

Electrical battery-powered handwheel with 20 mm hollow shaft, directly attachable to spindle.

For absolute measurements

Battery-powered absolute mini position indicator

Battery-powered absolute measuring and indicating system with external pluggable sensor

Battery-powered absolute 3-axis position indicator

Battery-powered absolute measuring system with integrated sensor on the back side of the indicating device.

Battery-powered absolute measuring and indicating system with large two-line LCD display

Controls

Single Axis

Compact single axis controller. The P40 is predestined for easy positioning applications.

A single axis controller without program memory.Suitable for simple positioning applications.

P8721 is a single axis controller with program memory. The program memory allows the processing of up to 200 address lines (proratable into blocks).

Single axis controller with an extensive parameter menu. P9521 with additional program memory.

Multiple Axes

for sheet metal shears. Intuitive interface and menu navigation, for the complete control of the cutting process.

Compact 2 axes controller.The P40 is predestined for easy positioning applications.

Low-Cost-Terminal with positioning functions up to 6 axes. This robust and compact controller can be used in a wide range of applications.

Touch screen terminal on the basis of the IPC which is characterized by an optimal price-performance ratio and easy handling.

P8822 is a 2 axes controller which is easy in handling and enables a fast parameterization

SensorsFor Lift

Installation kit for the quick and easy installation of the magnetic tape in the elevator shaft.

General